VCM2 manual: NEW module programming using Ford IDS software
Jan 09, 2014 Focom ford obd2 diagnosis software free focom interface full download Focom ford is obd2 diagnosis cable for for Ford vehicles. Focom ford obd2 diagnosis software newest version is 1.0.9419.
You need Ford IDS software, original or crack
You need a HQ VCM2 cloneSP177-C or SP177-C1
(VCM2 genuine definitely is the best solution, but a high-quality one should work great, not cheap crappy tools)
When installing a new module, the configuration data must be transferred from the old module beforeit is removed. The new module will then be programmed using this information. Use the followingsteps to download the data from the existing module and program the new module:
Step 1: Select the toolbox tab at the top of the screen
Step 2: Select “Module Programming”
Step 3: Select the tick mark or the Enter key
Step 4: Select “Programmable Module Installation”
Step 5: From the fly out menu, select the type of module to be installed
Step 6: Select the tick mark or the Enter key
Step 7: Make sure that an Internet connection has been established and then select “Confirm”
Step 8: Follow the instructions on the screen. These instructions vary depending on the type ofmodule being installed.
NOTE: Be sure to follow these instructions in the exact order that they are given. Do not remove or install any modules until instructed to do so. Failure to follow the instructions correctly may result in the configuration data received during vehicle identification to program incorrectly or not at all.
Step 8A: If Ford Module Programming was unable to retrieve the configuration data due to either
a non-functioning module or a module which was removed before the data was retrieved, the
application will request that the user obtain information from the Module Build Data (As Built)
database. Access to this database is included in the Ford Module Programming subscription. The
data can be obtained by doing the following:
- Go to the Motorcraft website (www.motorcraft.com)
- Go to the Technical Resources area
- Log in using the User ID and password set up when the subscription to Ford Module
Vcm Ii Software
Programming was purchased
- Select “My Subscriptions”
- Select “Ford Module Programming”
- Select “Module Build Data (as Built)”
- Enter the Vehicle Identification Number (VIN) and select “Submit”
- Write down the information that was requested by the Ford Module Programming
application
- Return to the Ford Module Programming application and enter the requested information
Step 9: If necessary, apply the reprogramming label to the PCM
If an emissions recall has been performed or a required emissions-related TSB has been completed,
![Vcm Vcm](https://i.ytimg.com/vi/ABH3DAGVOk8/maxresdefault.jpg)
an Authorized Modification label must be placed on the PCM. These labels can be purchased at the
parts counter of a Ford or Lincoln/Mercury dealership.
NOTE: It is the responsibility of the technician to inform the customer that Ford Motor Company will not reimburse the vehicle owner for field service actions that are not completed at a Ford or Lincoln/Mercury dealership.
Step 10: When the “Programming complete” screen appears, select the tick mark or the Enterkey. If PATS initialization is required, Ford Module Programming may automatically link to the PATSparameter reset and/or key relearn procedures. Two ignition keys may be required to complete the
PATS initialization procedure.
Step 10A: If PATS initialization is required and Ford Module Programming did not link to thatfunctionality automatically, go to the Toolbox tab and select “PATS”. Detailed instructionsare provided in Section 6.
Good tips you may need:
Where to buy VCM2 clone of high quality?
Where to buy VCM2 clone at the best price?
Ford IDS crack download: (TRY ON YOUR OWN RISK)
IDS 106: http://blog.obdexpress.co.uk/2017/08/02/fordmazda-ids-106-software-download-100-tested/
IDS 105: http://blog.obdexpress.co.uk/2017/05/22/ford-ids-105-02-mazda-ids-105-02-download-free/
IDS 104:
How to reprogram Ford PCM with vcm2 clone:
who like this article also viewed:
Ford VCMII IDS software has been updated to V97.01 (23/09/2015). Free IDS V97 and update instruction is provided below.
NOTE: IDS V97 is compatible with Ford VCM 2 scanner SP177-1,
SP177-C, SP177-C1SP177-C2. Do not work on other VCM2.
SP177-C, SP177-C1SP177-C2. Do not work on other VCM2.
Software version: IDS V97.1
Operating system: Windows XP/ Windows 7 on VMware (recommended)
Free download Ford IDS V97.1 software
http://www.fordservicecontent.com/Ford_Content/IDS/IDS-97.01_Full.exe
You can download form the link directly or download from Thunder (enter URL to download
directly), because the software is huge.
directly), because the software is huge.
How to update VCM2 IDS to V97?
1.Have old V81, V91 IDS installed
1) First install C81 Calibration files and then V86 IDS
2) Then install V91 IDS, if the software displays 3 day trial prompt, then continue to
install IDS V96, otherwise quit software installation and change another laptop to re-install software
install IDS V96, otherwise quit software installation and change another laptop to re-install software
3) After well install V96 IDS, install IDS V97 software
4) Update VCM2 firmware (following instructions below)
2. Have IDS V96 installed
If you already have VCM2 IDS V96 installed, then directly install V97 IDS and update
VCM2 firmware.
VCM2 firmware.
How to update Ford VCM 2 scanner firmware?
1) Press the power button on VCM2 scan tool main unit
2) Long-press on the power button, connect VCM2 with power supply, wait for all 4 indicators turn on, then release the button. Then connect VCM2 with computer via USB cable
3) Run IDS software, software will prompt to update firmware. Wait the update procedure is done.
4. Restart computer when firmware update is completed. Connect VCM2 kit with vehicle to
start diagnosing or programming functions.
start diagnosing or programming functions.
Driver for VXDIAG VCX NANO/ VCM 2:
http://www.obd2vip.com/download/vcx-nano-ford-mazda-driver-1-0-6-1224.zip
http://www.obd2vip.com/download/vcx-nano-ford-mazda-driver-1-0-6-1224.zip